ASTM D4595 PDF

This standard is issued under the fixed designation D ; the number immediately 1 This test method is under the jurisdiction of ASTM Committee D35 on. Designation: D – 09Standard Test Method for TE D Tensile Properties of Geotextiles by the Wide-Width Strip. ASTM D measures the tensile properties of geotextiles using a wide-width strip specimen tensile method. ASTM D is applicable to most geotextiles.

Author: Gagul Goltiktilar
Country: Sweden
Language: English (Spanish)
Genre: Photos
Published (Last): 26 February 2014
Pages: 466
PDF File Size: 16.61 Mb
ePub File Size: 14.48 Mb
ISBN: 542-6-15142-569-8
Downloads: 98219
Price: Free* [*Free Regsitration Required]
Uploader: JoJorn

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Special clamping adaptions may be necessary with strong geotextiles or geotextiles made from glass fibers to prevent them from slipping in the clamps or being damaged as a result of being gripped in the clamps.

ASTM D is applicable to most geotextiles that include woven fabrics, nonwoven fabrics, layered fabrics, knit fabrics, and felts that are used for geotextile application. Report the method of calculation.

On those fabrics, the contraction effect cited in 1. A low force range may be used to establish the point of the applied pretension force on the force?

ASTM D4595 Wide-Width Tensile Test Equipment for Geotextiles

Calculate secant tensile modulus using Eq 7 See Fig. The greater width of the specimen specified in this test method minimizes the contraction effect of those fabrics and provides a closer relationship to expected geotextile behavior in the field and a standard comparison.

The major problem encountered was de? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. It is the responsibility of the user of aatm standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. NOTE 5—Some clamping arrangements may lead to slack in the dd4595 within the gage area.

  MADMAPPER TUTORIAL PDF

Comparative tests 4d595 directed in 5. In any event, the procedure described in Section 10 of this test method for obtaining wide-width strip tensile strength must be maintained. Competent statistical assistance is recommended for the investigation of bias.

This helps maintain specimen integrity during wstm test. In some cases, it may also be caused by a concentration of stress in the area adjacent to the jaws because they prevent the specimen from contracting in width as the force is applied. In any event, the procedure described in Section 10 of this test method for obtaining wide-width strip tensile strength must be maintained.

The time of immersion must be sufficient to aastm the specimens thoroughly, as indicated by no signi? Comparative tests as directed in 5. The point from the zero force axis that the force?

This test method is asrm to most geotextiles that include woven fabrics, nonwoven fabrics, layered fabrics, knit fabrics, and felts that are used for geotextile application. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in the light of the known bias.

The determination of the wide-width strip force elongation properties of geotextiles provides design parameters for reinforcement type applications. Centrally, draw two lines running the full width of the specimen, accurately perpendicular to the length dimension and separated by mm 4 in. This axtm, by contrast, is greater than the length of the specimen. While such a procedure cannot be accepted in cases of dispute, it may be sufficient in sstm testing to d4955 the material to the standard atmosphere for testing for a reasonable period of time before the specimens are tested.

  LANGAGE PL7-3 PDF

We are confident d4955 we have what you are looking for. Competent statistical assistance is recommended for the investigation of bias. For secant modulus, state that portion of the force? These designs have been used in the laboratory and have provided reproducible tensile strengths.

Test Specimen Preparation 8.

ASTM D Wide-Width Tensile Test Equipment for Geotextiles

This standard does not purport to address all of the safety concerns, if any, associated with its use. Breaking toughness is calculated from work-to-break, gage length, and width of a specimen.

Some fabrics used in geotextile applications have a tendency to contract neck down under a force in the gage length area.

Some fabrics used in geotextile applications have a tendency to contract neck down under a force in the gage length area. The greater width of the specimen specified in this test method minimizes the contraction effect of those fabrics and provides a closer relationship to expected geotextile behavior in the field and a standard comparison.

The secant geotextile tensile modulus can be determined by dividing the force at any point along line Q9R9 or its extension by the elongation at the same point measured from point B9, de? Number each specimen and then cut it crosswise into two parts, one for determining the conditioned tensile strength and the other for determining the wet tensile strength; each portion shall bear the specimen number.

The sample may be taken from the end portion of a roll provided there is no evidence it is distorted or different from other portions of the roll.

On those fabrics, the contraction effect cited in 1.